Cisco CCNA Crash Course (200-301)
CSL Training is one of the prominent IT training institute offers CCNA Training in Dhaka for interested students. Throughout the world, CCNA 200-301 is the most valued IT certification and is a highly respected & sought-after credential. The full abbreviation of CCNA 200-301 is Cisco Certified Network Associate. It’s an IT certification developed by the famous brand Cisco. This certification will validate an individual’s level of skill through a series of network-related topics.
Cisco CCNA Training in Dhaka is considered as one of the high regarding certification in the networking field. If you want to get a high quality CCNA 200-301 training in Dhaka, then you are in the right place.
Course Objectives – CCNA Training
- Network Fundamentals
- Network Access Technologies
- IP (IPv4 & IPv6) Connectivity
- IP Services (ACL, HSRP, EtherChannel, DHCP, NAT, DNS)
- Security Fundamentals
- Network Automation and Programmability
- Implementing Network Device Security
- Network Device Management
Target Audience – CCNA Course
- IT Professional
- Network Professional
- Network Support Engineer
- Network Admin
- System Engineer
- Network Product Pre-sales engineer
Course Pre-requisite – CCNA Training
- Basic Computer Knowledge
- Data Communication Systems
- Networking Fundamental
- Computer Networking Components
- OSI References Model
- TCP/IP Protocols
Course Summary
Course Fee
৳ 12,000
Training Method
Offline/Online
Total Modules
6
Course Duration
48 Hours
Total Session
12
Class Duration
4 Hours
Details Course Outlines - CCNA Training
Lesson-01
Network Fundamental
- Lab 01 Observe How a Switch Operates (ARP
- Lab 02 Cisco Command-Line Interface (CLI) Introduction
- Lab 03 Perform Basic Router Configuration
- Lab 04 Perform Basic Switch Configuration
- Lab 05 Configure Basic IPv4 Connectivity
- Lab 06 Configure Basic IPv6 Connectivity
- Lab 07 Reset/Recover Router Password
- Lab 08 Upgrading IOS for Routers & Switches
Lesson-02
Network Access
- Lab 09 Configure and Verify Layer 2 Discovery Protocols (CDP)
- Lab 10 Configure and Verify LLDP Configuration
- Lab 11 Configure VLAN (Access, Data, Voice, Default and Trunk)
- Lab 12 Configuring InterVLAN Routing on Cisco L3 Switch
- Lab 13 Configuring Router on a Stick using Cisco Router
- Lab 14 Configure a Dynamic (VLAN) Interface
- Lab 15 Examining Spanning Tree (STP) Process on Switches
- Lab 16 Configuring Rapid-PVST and PortFast
- Lab 17 Configure and Verify EtherChannel (LACP mode and Load Balancing)
- Lab 18 Install and Configure Cisco Wireless LAN Controller (WLC)
Lesson-03
IP Connectivity
- Lab 19 Explore Packet Forwarding
- Lab 20 Implement IPv4 Static Routing
- Lab 21 Implement IPv4 Static Default Routing
- Lab 22 Implement IPv4 Floating Static Routing
- Lab 23 Configure and Verify Single-Area OSPF
- Lab 24 Implement IPv6 Static Routing
- Lab 25 Implement First Hop Redundancy Protocol (HSRP)
Lesson-04
IP Services
- Lab 26 Configure and verify DHCP, DHCP client and DHCP relay
- Lab 27 Configure Static NAT
- Lab 28 Configure Dynamic NAT
- Lab 29 Configure Port Address Translation (PAT)
- Lab 30 Configure and Verify NTP Server and Client
- Lab 31 Configure network devices for remote access using SSH
- Lab 32 Cisco IOS Syslog Configuration
Lesson-05
Security Fundamental
- Lab 33 Implement Device Hardening (Console, Enable, VTY Password)
- Lab 34 Secure Device Administrative Access
- Lab 35 Configure and Verify Switch Port Security
- Lab 36 Configure and Verify Standard ACL
- Lab 37 Configure and Verify Extended ACL
- Lab 38 Configure and Verify Named IPv4 ACL
- Lab 39 Implementing Wireless Security (WEP, WPA, WPA2, WPA3)
- Lab 40 Configure WLAN using WPA2 PSK using the GUI
- Lab 41 Configure Remote Access VPN & Site to Site VPN
- Lab 42 Implementing DHCP Snooping
- Lab 43 Implementing AAA (RADIUS) Authentication
Lesson-06
Project
- Lab 44 Design Multi POPs ISP Network